NRA-ILA ice cream social

On August 4th I was invited to go to an Ice Cream Social at the new NRA-ILA office in St Charles, MO. I signed in but did not take the 'Vote Obama Out' sticker that they were using to track who had signed in. They now have my name, address and the new email address for my volunteer position with the LGC.

There were some very earnest folks there. I did hear terms bandied about that I had anticipated hearing such as "socialism", "anti-gunners" and "Liberal" used as negative terms.

What I did learn was that despite being told the contrary, my perception of the NRA-ILA being vocally Republican was correct. I don't think that there has been a Democrat (non-DINO) in a place of leadership since the
ILA was formed.

When the NRA-ILA is willing to allow non-Conservative views to be expressed as part of their platform or at least not spending members' money on Conservative issues, I will consider joining.

So, who is the new Director of Merchandising for the Liberal Gun Club?

This guy! 

The Club President has been swamped for over the last year with things more important than t-shirts, bumper stickers and coffee mugs.  "How can that be?" you might ask.  Well, sometimes you have to ask for help to get things done, and he did.

What this means is that I get to find places that are either using 'Made in the US' swag, union workers to put designs on things or both.  With luck, I can find a Print on Demand company that does both or the result will be that only our custom orders will fill that goal.  I'm trying to not have a metric assload of swag being stored at my house with the LGC emblems on them.

If anyone has any leads on businesses that could be used, I'd appreciate it greatly.

What firearms law changes need to be made to make us safer?

Answer:  none.

A lot of my fellow liberals are calling for increasing the restrictions on guns in the wake of the Aurora, Colorado shootings.  I fundamentally disagree.  The actions of a lone nutcase should not be used as an excuse by the power elite to force law abiding gun owners to surrender their guns.

Calls for more 'reasonable' gun laws on Facebook have been met with the following quote from Yours Truly:

Explain to me who's definition of 'reasonable' we are going to use. I prefer George Mason and Thomas Jefferson's, they are two of the greatest Liberal minds we as a country have had.

Why not just scuttle the 4th and 5th Amendments and allow Anti Gun cops to check every house. I mean, they'd go into the safes and remove all of the legally owned guns. We'd be safe then, right?

The 2nd Amendment is an individual right thanks to the 1903 Militia Act. Sorry, I for one have NO issue with this at all.

Many other blogs have written about the perspective of firearms owners on the tragedy so I won't go into that here.  I maintain that Liberals should be the ones leading the fight to ensure that all parts of the Constitution are upheld and if anything is onoerous the proper steps be taken to change them.

Several folks have called for the 2nd Amendment to be re-written.  If they feel that this is something that the majority of the country would agree with, I encourage them to draft the Amendment, call a Convention and get 33 states to ratify the changes.  I also recommend that they not blame the 'Gun Lobby' when this measure fails. 

Lower is 100% finished

Went to the gun show today in St Charles, MO and got the parts needed to finish off my lower.  I got my buffer and spring from Mark's Armory's buttstocks and buffers page and am very pleased with it.

Since my last update, I have done the following:

• Sprayed the lower and grip with Rust-Oleum Dark Taupe paint and flat clear coat.
• Done a simple whip-tie with tan 550 para cord on the buffer tube.
• Attached a single-point to two point sling adapter on the rear plate consisting of 550 para cord tied with a bowline on a bite into the loop and a pair of standard bowlines on the ends.

Buffer tube installed

I fixed the issue I had with the front pivot pin detent without having to buy anything new or fancy.  I found a steel nail that was 3/32" in diameter and cut a length of it that would work as the detent.  Installation of this improvised detent pin went far better than the one supplied by CMMG.  Front pivot pin is now working as designed.

At this point, the last bits I need for my lower is the buffer (going with an "H" carbine buffer to start with) and the buffer spring.  Once I have those, I'll get a few cans of Rust-Oleum 'nutmeg' and 2-3 cans of clear flat enamel.  After the paint dries, I'll be wrapping the buffer with coyote 550 paracord.  I may add some red paracord into the mix to show off the weave pattern, not sure at this time.

Current plan for the upper will go one of two ways.  Either I'll drop $350 + S/H on a DSArms 11.5" flattop upper w/bolt carrier group or I'll part an 11.5" upper together.  It just depends on finances.  Odds are that I'll be parting one up with parts from Surplus Ammo which would cost more in the long run but would mean less money put out at once.  Since I have the vice blocks for the upper assembly as well as a good armorer's tool from ATI, I'm not worried either way.

Post LPK update

Ok, got my parts on Saturday to get the lower 75% finished, just need a carbine length buffer assembly and then it's on the parts that touch bullets.

Also, the M&P15 logo will end up being covered up by Flat Dark Earth epoxy paint.  I will possibly get that section engraved with either a replacement M&P logo or else go with the Minuteman from the Liberal Gun Club instead.

Next step is the buffer assembly and then on to the upper receiver!

After the whole build is done and I have function tested the pistol, I'll consider cutting down the LGC custom grips I have, but those will probably just get installed on the Rock Island Armory Tactical .45 I plan on getting instead.

                                              build as it stands on 6-11-2012

AR Pistol build

Finally got the partial funding to move a bit forward with my pistol build.  Yep, I said pistol.  I know, I know, Missouri allows Short Barreled Rifles to be owned by anyone that gets their Form 1 returned successfully from the ATF, but I am not ready for that just yet. 

Many of the folks mentioned in my will are not MO residents, so taking possession of an NFA firearm is tricky to say the least.  Also, who knows what the laws will be or where he will be living when my son is old enough to take possession.  On top of that, just handing the SBR off to someone that may want to shoot it is potentially an NFA violation which carries a felony charge and $25,000 fine.  So, no SBR until I get an NFA Gun Trust set up and approved.

Anyway, back to the build.

Previously, I showed my lower and Pearce Gripframe.  Now I have gotten some Magpul goodies that will go on the firearm along with the colorscheme I plan on using.  After getting a Magpul case for my iPhone, I found I like Flat Dark Earth (Magpul Urban Dark Earth is the Duracoat color I'll need to order for the metal bits) and it should make the firearm a bit better for use in hunting.

Parts shown:
Ambi-mounted sling backplate
Front and rear MBUS
Angled Forward Grip (ATF approved for pistols)
S&W stripped lower
Pearce 1911 grip frame
Magpul enhanced trigger guard



I have a CCMG lower parts kit and vice blocks to allow me to clamp down my firearm for assembly on order with Cabela's and will have them on 6/14.  After that, all I need is the carbine buffer assembly and the lower is done.  I also have a gas block/front sight heading my way from a friend in Russleville, MO.  Also I have an attachable m1913 rail coming in for the AFG to be mounted to whatever handguard I go with.

For the upper assembly, I am planning on a 10.5" 5.56 M4 barrel with standard front sight attached to an M3 'flat top' receiver.  For handguards, I plan on either a Magpul MOE foregrip or else a free-floated foregrip with top and bottom rails from Midwest Industries.  If I go withe the free floating handguard, I can mount the front MBUS without issue but it would cost more and require me to cut off the front sight tower from the gas block.  If I go with the Magpul handguard, the AFG would look almost like it was molded onto the guard and I would not have to cut off the front sight tower.

Once I get the buffer tube, then the temptation will be to get the Duracoat 'quick use' set so I can get everything the same tone of FDE. 

More pics and updates to follow!